Our Decision to Switch to Medtronic Minimed 630G Insulin Pump – Part 2

This part may be a bit long, so go get some coffee and settle in. There is a lot to cover here 🙂

Ahhhh….coffeeeeeee…. (Pixabay)

I started on the Medtronic 630G pump on 5/1/17 – the day I received it. This is a bonus of having a small endo office – they can pretty much work you in at any time for device training.

So, in the boxes were the pump box, sensor box, and meter box. Along with lots of papers and training books. I had also already watched the training videos and played with a demo too, so I had a general idea of what to expect.

Using the pump wasn’t my concern at all since it worked pretty similar to other pumps — it delivers insulin based on your settings. Okay, no biggie. The biggie for me was whether I could trust the CGM or not. This is a big question for many, especially if you are die-hard dedicated Dexcom user as well.

See, I had the 530G before with Enlite. I did not have good success at all. It was rarely correct, and I was going through sensors every 3 or so days. It wasn’t worth the hassle it was giving me. But, I had been keeping my eye on the 630G since it was available, and I wanted to see what other’s were experiencing. The consensus was that the 630G was much better somehow. I believe they updated the algorithm a bit, and it was supposed to be a vast improvement.

The game-changer that helped the transition:

I made the decision that others had (CarolCluka and CoolReeRee ) to keep my Dexcom sensor attached until I was fully comfortable. This lasted about 3 weeks. I kept my Dexcom connected to my Glooko account because I can connect Glooko to Medtronic Carelink, and I could see how they both compared. I was pleasantly surprised, to say the least:

Of course, there are times when the sensors didn’t line up perfectly, but as you can see, they’re pretty on-point with each other.

I’ve had pretty good success, and so much that I disconnected from my Dexcom after 3 weeks and felt completely comfortable doing so.

The good, the bad, and the tips…

Now, let me tell you… it hasn’t been all cupcakes and rainbows for the last almost-two-months. I did go through about a week or so of wildly inaccurate readings. So much that I reconnected my Dexcom. See, the problem is that you cannot jump into the Medtronic system with the experience of Dexcom. You have to wipe that mindset out and start over.

First and foremost, you have to calibrate at least twice a day, but it is recommended to be 3 times at a minimum, and 4 max. So, I’ve developed a routine – I calibrate when I wake up, again before lunch, and before bed. The system stays pretty accurate if I do that, which is no problem really, because it’s not hard to do. I’ve never been one to feel comfortable enough to dose off of my Dexcom, so I always test before eating. All it takes is a click to calibrate, and then a click to go to the bolus wizard. No big deal at all.

Second, there are rules: (I’m sure they could apply to Dexcom too to help make it be more accurate, but these are sort of a must-follow in my opinion if you are on Medtronic’s system)

  1. Follow the “B” rule when learning your own calibration schedule: Before breakfast, before lunch, before supper, before bed. Find three of those that fit YOUR schedule and when you know you’ll be least likely to be trending wildly (aka – no arrows)
  2. Do NOT calibrate if you have bolused in the last 2 hours. The sensor is less likely to be as accurate since you have bolused in that time, and a calibration could confuse the sensor.
  3. If the sensor is “off”, especially when waking up first thing in the morning, try drinking some water and walk around a bit. This gets the interstitial fluid moving around the sensor again. It will likely re-align itself within 30 minutes or so.
  4. Be patient. I cannot stress this enough. If coming from Dexcom, you may be used to the instantaneous calibrations. The sensor can take 10-15 minutes to accept a calibration, especially if the values are very different (up to 60mg/dL). If it is above 60mg/dL, try the drinking and walking bit. If it doesn’t realign, call tech support for help or a new sensor. They can help you upload your pump and look for specific things that could be interfering with the sensor communication.
  5. When inserting the sensor and taping, BE GENTLE! Taping the sensor head down too hard or pulling the transmitter tape flap too hard and tight on top of the transmitter can cause the sensor to pull out just a bit from the skin, which can cause big trouble. If you set it up softly, it will be nice to you.

After I called tech support, I found that I was being too rough with taping, and not being patient with the calibrations. Since then, I’ve been able to go back to Enlight sensor values only, and it’s been just as good as it was when I first started. Heck, it’s even caught real, legit lows that the Dexcom didn’t.

In the past couple of months, I have been greatly impressed with the CGM of the Medtronic 630G pump. I’ve caught myself at times in awe of it, really.

Why the 630G now and not wait for the 670G?

One question I was asked already on Facebook was “why not wait until the 670G?” The reason is that I wasn’t sure I could trust the sensor to make the call to give me insulin if I were going above range. Cutting off my basal for a couple of hours is one thing — giving me insulin when I don’t need it is a whole other realm, and I wanted to be sure I could trust the system. I am on the list for the 670G, and I should be able to get it next month once my sensor order is due (that’s how they time when you get it if you’re on the pathway program).

I am on the list for the 670G, and I should be able to get it next month once my sensor order is due (that’s how they time when you get it if you’re on the pathway program). I can use the pump similar to how the 630G works now when I get it, and then wait to be trained on “auto-mode” later. I am cautiously excited to see how it works, but I’m also not going to be entirely upset if it doesn’t live up to the hype I’ve seen. Mostly, because I know the experience is going to be different for everyone, and I know it can be a learning curve even if you’re coming over from the 630G.

And, to be completely honest, it would be the same hesitancy whether it was the Medtronic system or one that incorporated Dexcom. Anything that augments how my insulin is delivered, I’m going to be very hesitant about. I guess I’m just old-fashioned and have been burned by eagerness one too many times.

Where to view more if you’re interested:

I’ve been trying to keep this to myself and a few close friends in the beginning just in case this new experience caused me to be upset and disappointed. I prepared myself for the worst, thinking it would be no different than the 530G. Maybe that’s why I’m so much more surprised than I thought I would be.

So, instead of blowing up their phones with text or Facebook messages, I decided to revive my Sugar and Sites domain for Instagram and Tumblr, and get my thoughts out there.

You can click on the image and it will take you to the Instagram page I’ve been using. Let me know in the comments what you think, and if you have any other questions. From those, I’ll make a Part 3.

Which brings me to my next thought: I may begin transitioning from Sugabetic to Sugar and Sites overtime. I’ll still keep Sugabetic alive, but maybe on a free WordPress site. I’ll handle the transition as smoothly as possible, but there may be a few days that things will be down. Until then, feel free to follow me on IG for updates about the pump experience 🙂 

 

2 thoughts on “Our Decision to Switch to Medtronic Minimed 630G Insulin Pump – Part 2”

  1. Great points and thank you so much for the post, Sarah. Very glad you’ve found something that works best for you right now, and hope that stays the case. Totally understand there are “rules,” and that’s a huge part of using a MedT CGM. I’m just not a fan of that. To me, those rules are design flaws and I personally would’ve liked to have seen innovations happen more than they have in the past decade for MedT, especially since it can be done as seen with Dexcom and internationally-available CGM tech. But, I digress. To each their own, and that’s just my gripe. My big Q for you: As to the Lows, one of the huge issues I had with 530G with Enlite was false lows, when it would shut off based on inaccurate data. Any thoughts on that, here? Thank you again for this, and looking forward to hearing more on how it goes!

  2. In my mind, the biggest flaw with the old Enlite sensor was not the electrochemical part of it, but the mechanics of it: the wobbly transmitter,the uneven surface area and supplemental tape, etc. it made the whole insertion process, well, a process – and an inconsistent one at that. (There was no time to insert a sensor before work, and inserting before bed meant waking up in 2 and 6 hours to calibrate!). At first, it was the simplicity, not the accuracy, of the Dexcom that convinced me to switch. Like you, I’m reluctant.

    I’m glad to hear that the results are better, but I’d love to know if the mechanics or insertion-process of the new sensor have improved at all.

Tell me what you think!